Unb Hisense washer: unbalance alarm

Reviewed 2026-11-18 against 3 Hisense manuals. See sources.

What Unb means

Unb is Hisense’s “unbalance alarm.” The washer couldn’t get the load evenly spread around the drum, so it won’t spin it at full speed. Hisense gives two causes: laundry that has tangled together, and a load that is too light. [1, p. 58; 2, p. 42; 3, p. 45]

Hisense washers have a balance detection and correction system. When very heavy items such as bathrobes throw the drum off balance, the washer retries the spin several times and then slows down or stops spinning to protect itself, so clothes can come out wetter than usual. [1, p. 56]

While the washer is correcting an imbalance, the time remaining on the display holds still instead of counting down. [1, p. 55]

Safety first

Step-by-step owner checks

  1. Untangle the load

    Turn the washer off and open the door. Pull the laundry out, shake the items apart and put them back loosely around the drum. Close the door. [1, p. 58; 1, p. 56]

  2. Add towels if the load is small

    A load that’s too light can also trigger Unb. With the washer off, add more laundry or one or two towels, then close the door. [1, p. 58]

  3. Run the separate Spin program

    Choose the stand-alone Spin program and try again. Hisense gives this as the restart step for both causes. [1, p. 58]

  4. Don’t wash one heavy item on its own

    Hisense advises against washing a heavy quilt, a plush toy or a laundry bag by itself in the drum, because it can set off the unbalance alarm. Wash it with a few other items so the weight spreads out. [1, p. 31; 2, p. 20; 3, p. 22]

  5. If the washer shakes hard, check that it’s level

    All four feet should sit firmly on a solid, level floor and the washer shouldn’t rock when you push its top corners. Hisense says the slope under the washer shouldn’t exceed 3/4 inch (1.9 cm). Adjust the feet by turning them, extend them only as far as needed, and tighten the lock nuts afterward. [1, p. 28; 1, p. 56]

  6. On a new or recently moved washer, check the transport screws

    Hisense lists leftover transport screws and leftover bottom support foam as causes of violent shaking during spin. There are four transport screws on the back. Hisense says they must come out before the washer is used, and they go back in only if the washer is moved again. [1, p. 56; 1, p. 23; 1, p. 30]

Model differences:

Parts involved

Leveling feet

Hold the washer steady and level. Hisense says feet that are uneven, slide on the floor or are extended too far can cause vibration and noise. [1, p. 28]

Owner adjusts it; no routine replacement

Transport screws

Hold the drum still during shipping. Remove them before using the washer and keep them for any future move. Hisense says you can order replacements from the manufacturer if you lose them. [1, p. 23; 1, p. 30]

Owner-replaceable

Hisense treats Unb as a loading problem, not a failed part. Its manual doesn’t name any internal part behind the code. If Unb keeps coming back with a sensible, untangled load on a level washer, a technician needs to diagnose it. Hisense says to use only manufacturer-approved spare parts. [1, p. 59]

When to call a pro

Hisense prints its service phone number on the front of each manual. Have the model and serial number from the nameplate ready when you call.

Common questions

What does Unb mean on a Hisense washer?

Unb is Hisense’s unbalance alarm. The washer can’t spin the load evenly, usually because the laundry is tangled or the load is too light. Hisense’s fix is to untangle the load or add a towel or two, then run the separate Spin program.

Why are my clothes still soaking wet after the cycle?

When a heavy load stays off balance, the washer slows down or stops the spin to protect itself. Hisense also says too much foam can hurt spin results, so use a suitable amount of low-foaming detergent, and check that the spin speed isn’t set to 0 or No Spin. Then shake the clothes out and run Spin again.

Can I wash a single comforter or rug by itself?

Hisense advises against washing a heavy quilt, a plush toy or a laundry bag alone in the drum, because it can trigger the unbalance alarm.

Does the warranty cover damage from transport screws or bad leveling?

Hisense’s manual says damage from using the washer with the transport screws still in, or from leveling it incorrectly, is not covered by the warranty.

Other Hisense washer codes

Sources

  1. Hisense Canada, User's Operation Manual, WF5S2845BW front-load washer (models: WF5S2845BW (24 in., 3.1 cu. ft., 120 V)). PDF · support page. Accessed 2026-11-18. North American (120 V) manual. Page numbers are the printed page numbers in the English section.
  2. Hisense Malaysia, User's Operation Manual, WF105M3 washer (models: WF105M3, WF105M3*). PDF. Accessed 2026-11-18. Non-US model. Used only to confirm that the code meanings match across Hisense front-load washers.
  3. Hisense New Zealand, User's Operation Manual, HWF5I9014 washer (models: HWF5I9014, HWF5I9014B, HWF5I9014W2/W3, HWF5I9014B2/B3). PDF. Accessed 2026-11-18. Non-US model. Used only to confirm the code meanings and the "Confirm Start" step on newer controls.

Code meanings come from the Hisense WF5S2845BW manual (sold in Canada, 120 V) and match the Hisense WF105M3 and HWF5I9014 manuals. Hisense says some codes only apply to certain models, so check the fault table in your own manual too. Wording on this page is our own summary of those documents. Points without a citation are our general advice on when to stop and get help, not manufacturer statements.